IBM OS 2 Installation Guide For HP Net Servers - Info and Reading Options

The Internet Archive:

IBM OS/2 Installation Guide for all Hewlett-Packard NetServers<br /><br />NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version E.10.00 or L.16.00. If you don't have the E.10.00 or L.16.00 version CD-ROM and you're obtaining this document from the HP NetServer web site as a reference to install an operating system, be sure to also check the HP NetServer web site for the latest available drivers.<br /><br />©Copyright Hewlett-Packard Company<br />March 19, 1999<br />(This document is only available in English.)<br />Introduction<br /><br />The objective of this document is to help Hewlett-Packard customers install OS/2 on a HP<br /><br />NetServer system. For additional information on Hewlett-Packard NetServers refer to the HP<br /><br />Information Assistant on the HP NetServer Navigator CD-ROM.<br /><br />Table of Contents<br />Before You Begin<br />Section 1. Installation Tips and Considerations<br />Tip 1) Extended Translation Setting<br />Tip 2) Extending Disk Capacity Beyond 1 GB<br />Tip 3) Formatting Disk Partitions Larger than 2 GB<br />Tip 4) Device Allocation Under OS/2<br />Tip 5) RAM Greater Than 192 MB<br />Tip 6) Performance Tuning<br />Tip 7) Troubleshooting System Hangs When Loading CONFIG.SYS<br />Tip 8) OS/2 Warp Server Installation Issues<br />Tip 9) How to View the Resources Used by an Adapter<br />Tip 10) How to Run the HPVGSET.EXE Utility from the Navigator CD-ROM<br />Tip 11) 4GB RAM Support in OS/2<br />Tip 12) HPFS386 Drive cache size issue on systems with 4GB RAM<br />Tip 13) When using HP NetRAID install the driver MRAID.ADD<br />Tip 14) Getting Trap 00D when booting OS/2<br />Tip 15) Getting Trap 008 during extensive disk/network I/O<br />Tip 16) Specific to E Series NetServers: How to boot from a NetRAID adapter while a<br />2910Bui SCSI card is present on the system<br />Tip 17) IRQ sharing can cause system hangs<br />Tip 18) Adaptec driver AIC7870.ADD 133496 12-Jan-1998 or later is required for 2940UW<br />with rev B chip set<br />2<br />Tip 19) Configuring IDE drives as boot device<br />Tip 20) LPr CD-ROM must be configured as "Non-Listed IDE CD-ROM"<br />Tip 21) NetServer LH 3 Embeded SCSI and Raid Adapter Configuration<br />Tip 22) Installing multiple D5013 NICs<br />Tip 23) "Unable to Access the Hard Drive error" message during OS/2 installation<br />Tip 24) IBM's Recommended Procedure Installing OS/2 with New AIC78XX.ADD<br />Tip 25) Fixpak 40 Required for Memory Dump Functionality<br />Consideration 1: Choose the Booting Controller<br />Consideration 2: Selecting the Boot Drive Capacity<br />Consideration 3: Choosing the Boot Drive ID off Embedded Adaptec SCSI<br />Section 2. Creating the HP Drivers/Utilities diskette<br />Procedure One<br />Procedure Two<br />Section 3. OS/2 CD-ROM Installation Procedures<br />Installing Warp 3.0 or Warp Conn. 3.0 or Warp Server 4.0<br />Detailed Procedure for Installing Warp 3.0, Warp Conn. & Warp Server 4.0<br />Installing Warp 4.0 or Warp Server SMP 4.0<br />Section 4. Installing Hewlett-Packard NIC's<br />Installing OS/2 LAN Services for use with the HP J2973A or J2970A 10BaseT PCI LAN<br />Adapter (CD-ROM)<br />Installing LAPS Separately<br />HP J3171A/D5013A PCI Ethernet Adapters<br />General installation - LAN Server and OS/2 Requester (4.0 or 3.0)<br />Advanced Settings<br />Section 5. On-line Information and Software Sources

Search for “IBM OS 2 Installation Guide For HP Net Servers” downloads:

Visit our Downloads Search page to see if downloads are available.

Find “IBM OS 2 Installation Guide For HP Net Servers” in Libraries Near You:

Read or borrow “IBM OS 2 Installation Guide For HP Net Servers” from your local library.

• The WorldCat Libraries Catalog: Find a copy of “IBM OS 2 Installation Guide For HP Net Servers” at a library near you.